LCGB Forums

Posted: **Tue Nov 15, 2016 11:16 am**

Hi all

Would anyone be able to give me some base carb settings for a mildly tuned TS1 225, dellorto phbh 30mm running initially with a bgm clubman. I thought I'd see this question posted before but I've had a look & just can't find it so.......

Any guidance much appreciated thanks.

Cheers Mark.

Posted: **Tue Nov 15, 2016 1:23 pm**

ladsdad wrote:Hi all

Would anyone be able to give me some base carb settings for a mildly tuned TS1 225, dellorto phbh 30mm running initially with a bgm clubman. I thought I'd see this question posted before but I've had a look & just can't find it so.......
Any guidance much appreciated thanks.

Cheers Mark.

Mark, I have just given this to Toddy also, and this is what I ran on mine but with a Franspeed Supertourer and it went really well with no bogging and good plug colours throughout:-

Main 135
Pilot 55
Choke 70
Slide 40
Atomiser AV 266
Needle X7
Float Valve 200

N.B. This is only a guideline and not a recommendation without Dyno and / or plug chops.

Hope this helps you a bit Mark,

Rich'

Posted: **Mon May 01, 2017 12:48 pm**

Rich Oswald wrote:
ladsdad wrote:Hi all

Would anyone be able to give me some base carb settings for a mildly tuned TS1 225, dellorto phbh 30mm running initially with a bgm clubman. I thought I'd see this question posted before but I've had a look & just can't find it so.......
Any guidance much appreciated thanks.

Cheers Mark.

Mark, I have just given this to Toddy also, and this is what I ran on mine but with a Franspeed Supertourer and it went really well with no bogging and good plug colours throughout:-

Main 135
Pilot 55
Choke 70
Slide 40
Atomiser AV 266
Needle X7
Float Valve 200

N.B. This is only a guideline and not a recommendation without Dyno and / or plug chops.

Hope this helps you a bit Mark,

Rich'

Found this researching my issue. I have a BGM Clubman and a PHBH 30mm also was gonna follow the above to get started and maybe go ram breathe easy after a while of running open mouthed (which I can deal with later)......any idea on the above set up where the needle position would sit ?

AND....if I go with a breathe easy filter, presumably would just up jet it ?

Posted: **Mon May 01, 2017 6:21 pm**

carefull with that float valve, are you sure it wasn't a 300?

Posted: **Mon May 01, 2017 7:26 pm**

No its definitely a 200 float valve, I think the Carb (second hand new) must have been set up for a 150 small block previously......Looking at tables it seems the 200 float valve was used in some Imola 185 set ups.

Posted: **Tue May 02, 2017 9:56 am**

hullygully wrote:carefull with that float valve, are you sure it wasn't a 300?

I should have recommended a 300 float valve Mickey as that is what I was running. Sorry for the error.

The needle was on P2 (from the top).

Rich'

Posted: **Tue May 02, 2017 10:32 am**

Lucky someone's paying attention.... Cheers Mickey.

Posted: **Tue May 02, 2017 11:59 am**

ladsdad wrote:Lucky someone's paying attention.... Cheers Mickey.

Posted: **Tue May 02, 2017 12:13 pm**

ladsdad wrote:Lucky someone's paying attention.... Cheers Mickey.

Makes a change from his navigation skills

Posted: **Fri Mar 09, 2018 9:34 pm**

Rich Oswald wrote:
ladsdad wrote:Hi all
Richard what gearing was run on this please>>?
cheers.

Would anyone be able to give me some base carb settings for a mildly tuned TS1 225, dellorto phbh 30mm running initially with a bgm clubman. I thought I'd see this question posted before but I've had a look & just can't find it so.......
Any guidance much appreciated thanks.

Cheers Mark.

Mark, I have just given this to Toddy also, and this is what I ran on mine but with a Franspeed Supertourer and it went really well with no bogging and good plug colours throughout:-

Main 135
Pilot 55
Choke 70
Slide 40
Atomiser AV 266
Needle X7
Float Valve 200

N.B. This is only a guideline and not a recommendation without Dyno and / or plug chops.

Hope this helps you a bit Mark,

Rich'

Posted: **Tue Mar 13, 2018 7:42 pm**

Toddy wrote:
ladsdad wrote:Lucky someone's paying attention.... Cheers Mickey.

Makes a change from his navigation skills

LCGB Forums

TS1 30mm dellorto carb settings

TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings

Re: TS1 30mm dellorto carb settings