Lambretta '59 series 1 frame steering cone (lower)

[al pushpak]

Hi, in the process of renewing my steering bearings & i noticed the bottom race is quite pitted so I want to replace it, does anyone know where I can purchase the correct one for my '59 series 1 from ?as they seem to vary from frame to frame. thanks for any info

[bike grim]

Scootopia

[ULC Soulagent]

Scootopia

+1

[al pushpak]

Thanks for your replies,I've looked on the scootopia website & the only ones I can find state they are not suitable for series 1 will keep searching

[bike grim]

https://www.riminilambrettacentre.com/e ... ers-1.html

[al pushpak]

Nice one bike grim, cheers for that

[ULC Soulagent]

Or
http://www.scooterrestorations.com/lamb ... 1-2-and-3/

[bike grim]

No prob. Although I did get mine from Scootopia it was around 3 years ago so obvsiously not got them anymore

[jacktheripper]

if you havnt managed to get any i have 2 x sets

[al pushpak]

Thanks for the offer I managed to source one from cam lam in the end, the type I needed was for the earlier series 1 which was also fitted to some ld's apparently (shorter inner sleeve)

[al pushpak]

Well, the search goes on! thought I'd got a new lower fame cone bearing race sorted, ordered one from camlam which stated ld / early series 1 & when it arrived the inner sleeve was about 6mm longer than my original one which measures 14mm so obviously it won't fully fit all the way in because of the lip/ridge inside the lower fork tube! does anybody know who sells the correct one for my scoot thanks for any info

[HxPaul]

If the length is the only difference,cant you get an engineering shop to cut the extra 1cm off.And are you sure that the length is 14cm and not 14mm,14cm is 5 1/2 inches.

[al pushpak]

Yes, it's 14mm!! sorry maths was never my greatest subject so as I've stated in my previous post the one I ordered is 6mm too high, yes I guess I could have it machined down cheers

[dickie]

Yes, it's 14mm!! sorry maths was never my greatest subject so as I've stated in my previous post the one I ordered is 6mm too high, yes I guess I could have it machined down cheers

For something as simple as that, you could do it yourself with a decent hacksaw and a file.

[Phil D]

Yes, it's 14mm!! sorry maths was never my greatest subject so as I've stated in my previous post the one I ordered is 6mm too high, yes I guess I could have it machined down cheers

For something as simple as that, you could do it yourself with a decent hacksaw and a file.

This is exactly why nothing ever fits you shouldn't have to start hacksawing stuff.

[dickie]

For something as simple as that, you could do it yourself with a decent hacksaw and a file.

This is exactly why nothing ever fits you shouldn't have to start hacksawing stuff.

No, it's not "exactly why nothing ever fits" but it is a contributory factor.

Also, as the al pushpak is clearly having a bit of difficulty with this, I thought I'd use the forum to offer him a solution; which he may or may not take up.

Happy mother's day.

[Phil D]

For something as simple as that, you could do it yourself with a decent hacksaw and a file.

This is exactly why nothing ever fits you shouldn't have to start hacksawing stuff.

No, it's not "exactly why nothing ever fits" but it is a contributory factor.

Also, as the al pushpak is clearly having a bit of difficulty with this, I thought I'd use the forum to offer him a solution; which he may or may not take up.

Happy mother's day.

Thanks she passed away some years ago.

[holty]

hi, if its just too long i can stick it in my lathe and remove the extra length for you if your stuck, where in the country are you ?
you could post it to me ?
holty

[al pushpak]

Hi Holty, thanks very much for the offer, I've decided to order one from Rimini Lambretta which is what I should have done in the first place oh well , another lesson learnt! thanks again though